Dakota Digital RET Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 25

background image

650066

17

WATER TEMP SETUP

Press and hold SW 1 switch while turning the key on. Release the switch. When

“WATER” is displayed, press the switch again and then release it. The message display should
switch between “UNIT”, “WARN” and “TEST”.

METRIC SELECTION

If you are setting the system up for metric displays, press the switch when “UNIT” is

displayed.

Press and release the switch until “KPH C” is displayed.
Press and hold the switch unit “DONE” is displayed.

Temp warning setup

When “WARN” is displayed press and release the switch.
The current warning point will be displayed.
Press and release the switch until the desired setting is displayed.
Press and hold the switch until “DONE” is displayed.

OIL PRESSURE SETUP

Press and hold SW 1 switch while turning the key on. Release the switch. When “OIL” is

displayed, press the switch again and then release it. The message display should switch
between “WARN” and “TEST”.

Pressure warning setup

When “WARN” is displayed press and release the switch.
The current warning point will be displayed.
Press and release the switch until the desired setting is displayed.
Press and hold the switch until “DONE” is displayed.

DIM PRESET SETUP

Press and hold SW 1 switch while turning the key on. Release the switch. When “DIM”

is displayed, press the switch again and then release it. 88 or 888 will be displayed on the fuel,
oil, volt, and water displays. The system will dim down to the current preset level.

Press and hold SW 1 until the desired night brightness is shown. When the system

reaches its lowest brightness it will start over again at full brightness.

Once the night brightness is correct, press SW 2 to save it.

«
...
17
18
19
20
21
...
»

Содержание RET


























Отзывы:

Нет отзывов

Похожие инструкции для RET

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: Paratec Страницы: 8

Бренд: J+J Страницы: 33

Бренд: Baccara Страницы: 16

Бренд: Bang & Olufsen Страницы: 36

Бренд: Mad Catz Страницы: 4

Бренд: CALEFFI Страницы: 2

Бренд: CALEFFI Страницы: 12

Бренд: Caliber Страницы: 6

Бренд: Lawler Страницы: 4

Бренд: Hama Страницы: 46

Бренд: Galcon Страницы: 35

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Veeder-Root Страницы: 27

Бренд: Valve Concepts Страницы: 18

Бренд: K&K Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды