DAINIPPON SCREEN PLATE RITE 4300 Скачать руководство пользователя страница 134

Страница: 134 / 167

PT-R4300 USERS MANUAL

6-12

Wash the external cover filter with water or a neutral detergent.

Allow the external cover filter to dry completely, and then reinsert it in the
external cover.

Align the two tabs on the bottom of the external cover with the rectangular holes
on the unit, and insert the external cover into the unit.

External cover filter

External cover

External fan

4. Cleaning the External Cover Filter

Clean the external cover filter by following the procedure given below.

Remove the external cover, and then remove the external cover filter from the
external cover.

Reset the consumable timer in the user settings. For more details, refer to
Chapter 5 “12. Checking the Running Time and Setting the Consumable
Timers.”

Tab

Rectangular hole

External cover

Fig. 6-17 Removing the external cover filter

Fig. 6-18 Attaching the external cover filter

Содержание PLATE RITE 4300








































































































































































Результаты поиска

Содержание PLATE RITE 4300

Отзывы:

Бренды по названию

Популярные бренды

DAINIPPON SCREEN PLATE RITE 4300, Руководство пользователя

Результаты поиска

Содержание PLATE RITE 4300

Отзывы:

Бренды по названию

Популярные бренды