manualshive.com logo in svg

Daikin FTKS20CVMB, Руководство по обслуживанию

Поделиться
Скачать
Daikin FTKS20CVMB Скачать руководство пользователя страница 142

SiENBE04-401A

Troubleshooting

Service Diagnosis

133

4.19 Output Over Current Detection

Remote control 
Display

L5

Method of 
Malfunction 
Detection

An output over-current is detected by checking the current that flows in the inverter DC section.

Malfunction 
Decision 
Conditions

„

A position signal error occurs while the compressor is running.

„

A speed error occurs while the compressor is running.

„

An output over-current input is fed from the output over-current detection circuit to the 
microcomputer.

„

The system will be shut down if the error occurs 255 times.

„

Clearing condition: Continuous run for about 10 minutes (normal)

Supposed 
Causes

„

Over-current due to defective power transistor

„

Over-current due to wrong internal wiring

„

Over-current due to abnormal supply voltage

„

Over-current due to defective PCB

„

Error detection due to defective PCB

„

Over-current due to closed stop valve

„

Over-current due to compressor failure

„

Over-current due to poor installation condition

Содержание FTKS20CVMB























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды