manualshive.com logo in svg

Daikin FTKS20CVMB, Руководство по обслуживанию

Поделиться
Скачать
Daikin FTKS20CVMB Скачать руководство пользователя страница 130

SiENBE04-401A

Troubleshooting

Service Diagnosis

121

Troubleshooting

Check No.5

Refer to P.139

Check No.6

Refer to P.140

Check No.11

Refer to P.143

Correct.

Reconnect.

Replace the four way valve 
coil.

Replace the outdoor unit 
PCB.

Reconnect in position.

Replace a defective 
thermistor.

Refer to the refrigerant line 
check procedure.

Replace the four way valve 
(defective or dust-clogged).

(R3040)

Caution

Be sure to turn off power switch before connect or disconnect connector, 
or parts damage may be occurred.

Four way valve coil 

disconnected (loose)?

YES

YES

NO

Functioning     

NO

C

heck No.

 11

Check the refrigerant line.

Malfunctioning     

z

 Insufficient gas

z

 Water mixed

z

 Stop valve defective 

Harness out of connector?

NO

YES

Disconnect the

 harness from 

the connector. 

Resistance between 

harnesses about 

3k

Ω

±0.5k

Ω

?

Malfunctioning  

Functioning

C

heck No.

 5

Check the four way valve 

switching output.

YES

NO  

Any thermistor disconnected?

Malfunctioning  

Functioning  

C

heck No.

 6

Check the thermistors.

Check the continuity of the four 
way valve coil and harness.

Содержание FTKS20CVMB























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды