manualshive.com logo in svg

Daikin FTKS20CVMB, Руководство по обслуживанию

Поделиться
Скачать
Daikin FTKS20CVMB Скачать руководство пользователя страница 137

Troubleshooting

SiENBE04-401A

128

Service Diagnosis

Troubleshooting

Check No.6

Refer to P.140

P4

 : Radiation fin thermistor

J3

 : Discharge pipe thermistor

J6

 : Outdoor heat exchanger thermistor

H9

 : Outdoor air temperature thermistor

Turn on the power again.

Reconnect.

Reconnect.

Replace defective one(s) of 
the following thermistors.

z

  Radiation fin thermistor

z

  Discharge pipe thermistor

z

  Outdoor heat exchanger

 thermistor

z

  Outdoor air thermistor

Replace the following 
thermistor.

z

  Indoor heat exchanger

 thermistor

Replace the outdoor unit 
PCB. (Replace the indoor 
unit PCB.)

(R4097)

Caution

Be sure to turn off power switch before connect or disconnect connector, 
or parts damage may be occurred.

Error displayed again 
on remote controller?

NO

YES  

YES

YES

NO    

Indoor 

heat exchanger thermistor 

functioning?

NO

Connector or thermistor 

disconnected?

NO

YES

Normal?

Check No. 6

Check the thermistor resistance 
value.

Check No. 6

Check the indoor heat exchanger 
thermistor resistance value in the 
heating mode.

Содержание FTKS20CVMB























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды