manualshive.com logo in svg

Daikin EHS157034, Руководство по эксплуатации

Поделиться
Скачать
Daikin EHS157034 Скачать руководство пользователя страница 48

Operating instructions

48

Daikin RoCon HP

Daikin Controller

008.1420844_13 – 02/2016

6 

x

 Parameter settings

6.2.4 Level "DHW Configuration"

Parameter

Description

Access

Setting range

Min / Max

Factory 

setting

Increment

BE

HF

Circl-Pump DHW

Setting for activating a circulation pump. 
Off: Optional circulation pump operates according to the timer programme [Circulation Time].
On: The optional circulation pump operates synchronously with the switching timer program 
activated for generation of hot water.

E

E

Off
On

Off

-

Circl-Pump Interval

Setting the interval control for an optional circulation pump. 
Off: Deactivated The circulation pump operates continuously throughout the enabled time of 
the assigned switching timer program (parameter [Circl-Pump DHW]).
Otherwise: The circulation pump runs cyclically (duty ratio: pump running time = set value 
every 15 min).

E

E

Off, 

1 - 15 min

Off

1 min

Anti-Legionella day

Setting the day for the thermal disinfection of the circulating tank.
Off : No thermal disinfection
Monday - Sunday Day for thermal disinfection
Mon - Sun: Daily thermal disinfection

E

E

Off, 

Monday

... 

Sunday,

Mon - Sun

Off

-

Anti-Legionella time Setting the start time of the thermal disinfection of the hot water circulating tank (format 

hh:mm).

N

E

00:00 - 23:45

03:30

15 min

Anti-Legionella temp Setting the hot water target temperature during thermal disinfection of the hot water circulat-

ing tank (format hh:mm).

N

E

60 - 70 °C

 65 °C

1 °C

Max DHW loading 

Setting limits the time period for hot water generation to the set target value [T-DHW Set-
point]. After expiry of this time period, the controller automatically returns to the previously 
active operating mode. The hot water generation takes place at the actual set value.

N

E

0 - 240 min

60 min

10 min

DHW Off Time

Setting the block time following completion or interruption of a hot water generation cycle. 
New demand of hot water generation is satisfied only after expiry of this block time.

N

E

0 - 180 min

30 min

10 min

Tab. 6-4 Parameter in rotary switch setting "Configuration" level "DHW Configuration"

6.3

Rotary switch setting: DHW Install 

Parameter

Designation

Access

Setting range

Min / Max

Factory 

setting

Increment

BE

HF

1x Hot Water

Start of the one-off heating up of the hot water and the set value [T-DHW Setpoint 1], inde-
pendent of the heating programmes.

E

E

Off
On

Off

-

Hyst HP

Switching threshold hot water charging
Setting of the temperature difference to which the temperature in the domestic hot water 
storage tank compared to the current target hot water temperature [T-DHW Setpoint] can 
drop before the heat pump is switched on to provide hot water.

E

E

2 - 20 K

7 K

1 K

Timer BOH

Delay time after which the reserve heating may support the heat pump in hot water charg-
ing (see section 3.6.7).

E

E

20 - 95 min

50 min

1 min

Tab. 6-5 Parameter in rotary switch setting "DHW Install"

6.4

Rotary switch setting: Operating Mode 

Parameter

Designation

Access

Setting range

Min / Max

Factory 

setting

Increment

BE

HF

Standby

In this operating mode, all internal functions are turned off. Frost protection remains active 
and a blocking protection for the pump is guaranteed.
All controllers integrated in the RoCon-system via the CAN bus are also switched at a higher 
level to the operating mode when this setting is selected.

 Outputs are not free of voltage always.

E

E

-

Reducing

The internal heating circuit provides continuous (24 h per day) regulation to the para-
metrised setback temperature. The hot water generation takes place according to 

[DHW Program 1].

E

E

-

Heating

The internal heating circuit provides continuous (24 h per day) regulation to the para-
metrised day set room temperature (heating). The hot water generation takes place accord-
ing to [DHW Program 1].

E

E

-

Cooling

The internal heating circuit provides continuous (24 h per day) regulation to the para-
metrised day room temperature set (cooling). The hot water generation takes place accord-
ing to [DHW Program 1].
Frost protection remains active and a blocking protection for the pump is guaranteed.

E

E

-

Summer

The internal heating circuit is turned off. Frost protection remains active and a blocking pro-
tection for the pump is guaranteed. The hot water generation takes place according to 
[DHW Program 1].
All controllers integrated in the RoCon-system via the CAN bus are also switched at a higher 
level to the operating mode when this setting is selected.

E

E

-

Automatic 1

The internal heating circuit regulates according to the parametrised timer programme 

[HC Program 1] with the individual day room temperatures set. The hot water generation 
takes place according to [DHW Program 1].

E

E

-

Automatic 2

The internal heating circuit regulates according to the parametrised timer programme 

[HC Program 2] with the individual day room temperatures set. The hot water generation 
takes place according to [DHW Program 2].

E

E

-

Tab. 6-6 Parameter in rotary switch setting "Operating Mode"

Содержание EHS157034

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды