manualshive.com logo in svg

Daikin EHS157034, Руководство по эксплуатации

Поделиться
Скачать
Daikin EHS157034 Скачать руководство пользователя страница 43

6 

x

 Parameter settings

Daikin RoCon HP 
Daikin Controller
008.1420844_13 – 02/2016

Operating instructions

43

Interlink fct

Configuration for systems operating with 2 different inflow target temperatures 

(see section 3.6.6).
A possible use for this might be the additional integration of a FWXV(15/20)AVEB in a 
surface heating and cooling system.
Requirement: 2 room thermostats need to be connected to plug connection J16 on the 
Daikin Altherma EHS(X/H).

–

Off: Deactivated

–

On: Evaluation of 

 and cooling 

 switching contacts at plug connection J16 

on the RoCon BM1 circuit board.
Activation of cooling mode only possible by changing operating mode to "Cooling" 
(see section 3.4.2).
Setting for the parameter [Room thermostat] no longer evaluated.
a)

Open switching contacts: only frost protection active.

b)

Operating modes "Heating" and "Automatic 1" / "Automatic 2" active during 
switching cycles in day mode.

–

Closed switching contact heating 

 = IL1:

→

The system operates according to the normal infeed target temperature 
according to the parameter settings in 

"HC Configuration"

 > 

"Heating"

.

–

Closed switching contact cooling 

 = IL2:

→

The system operates according to the increased inflow target temperature 
(normal inflow target tempe value of parameter [T-Flow CH adj]. 

Priority if both switching contacts are closed.

c)

"Cooling" operating mode active.

–

Closed switching contact heating 

 = IL1:

→

The system operates according to the normal infeed target temperature 
according to the parameter settings in 

"HC Configuration"

 > 

"Cooling"

.

–

Closed switching contact cooling 

 = IL2:

→

The system operates according to the reduced inflow target temperature 
(normal inflow target temperature - value of parameter [T-Flow Cooling adj]. 
Priority if both switching contacts are closed.

N

E

Off
On

Off

-

MF 1 Config 

Configuring the multi-function output (230 V, connection J14):
0: The output has no function.
1: Gathering pump – the output becomes active as soon as a heating circuit of the sys-
tem indicates a heat demand to the heat generator.
2: Circulation pump – the output is activated in accordance with the timer programme 
of the circulation pump or in accordance with the timer programme of the hot water 
generation, depending on the parametrisation (see chapter 3.4.7). 
3: Delivery pump – the output is active as soon as there is a heat demand for the direct 
heating circuit of the heat generator.

N

E

0 - 3

2

1

Air Purge

Activation of automatic bleeding of the Daikin Altherma EHS(X/H) and the connected 
heating circuit (see section 3.6.10).
Off: Deactivated
On: Start of Air Purge

N

E

Off
On

Off

-

PWM Config

Max Perform Pump

Upper limit for modulation of the pump output

N

E

20 - 100 %

100 %

1 %

Min Perform Pump

Lower limit for modulation of the pump output

N

E

10 - 100 %

50%

 1 %

Sensor Config

Outside Config

Configuration of the optional external temperature sensor RoCon OT1:
Off: No sensor evaluation
On: Sensor evaluation activated. This sensor is evaluated for determination of the set 
flow temperatures (see chapter 3.6.4) and displayed in the standard display). An error 
message is generated if an outdoor temperature sensor is connected.

N

E

Off
On

Off

-

Storage Config

Configuration of water heating:
Inactive: No function for hot water generation.
Sensor: Function for hot water generation is activated. A circulating tank temperature 
sensor is evaluated for hot water generation (if no circulating tank temperature sensor 
is connected, a fault message is generated).
Thermostat: Function for hot water generation is activated. A thermostatic switch (On 
/ Off) is evaluated for hot water generation, and where "open brackets" are evaluated 
as "no demand".

N

E

Inactive

Sensor

thermostat

Sensor

-

Pressure Config

Configuring the sensor for assessment of the system water pressure:
Off: No sensor evaluation
On: Sensor evaluation activated (if no pressure sensor is connected, a fault message 
is generated.)

N

E

Off
On

On

-

Outside Temp Adap Individual adapting for the measured value of the outdoor temperature relevant for the 

Controller.

N

E

-5.0 to +5.0 kW

0,0 K

0.1 K

Terminaladress

Setting the terminal ID of the control unit for system access. The set value must be ap-
plicable for the entire system. Confirmation of this parameter using the rotary switch 
reinitialises the controller.
All settings, except "Off", empower the user of the control unit to activate the terminal 
function and thus to operate all RoCon system components with a valid device ID 

(see chapter 3.4.9 and 4.1).

N

E

Off, 0 - 9

Off

1

System Config

System configuration of the unit, consisting of the sensor configuration and data bus 
configuration. If you answer "yes" to the enquiry about using the standard configuration 
when starting the unit for the first time, the basic configuration for the installed heat 
generator will be activated automatically. 
Confirmation of this parameter setting as 

"inactive"

 or 

"delete

" using the rotary switch 

reinitialises the controller. A fault message follows. After this the rotary switch must be 
set to the position 

"Info"

. Use the rotary switch to select the required menu item.

N

E

Inactive

Active

Delete

Active.

-

Sub-

le

vel

Parameter

Description

Access

Setting range

Min / Max

Factory 

setting

Increment

BE

HF

Содержание EHS157034

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды