DAF 95XF Скачать руководство пользователя страница 40

Страница: 40 / 188

MAINTENANCE SCHEDULE

Maintenance intervals

series

1-2

1.2 EXPLANATORY NOTES ON THE MAINTENANCE SCHEDULE

MAINTENANCE GROUP CLASSIFICATION

Depending upon the use to which the vehicle is
put, the vehicle is placed in maintenance group
I, II or III.

Maintenance group I

Operation on building sites, in quarries, etc.
-

Operation on unmetalled roads

Operation in dusty environments

Sanitation department vehicles

Distribution transport with an annual
mileage up to 30,000 km.

Maintenance group II

Urban and regional transport
-

Distribution transport in cities

Traffic between adjacent villages/cities

Maintenance group III

(Inter)national traffic
-

Long-distance/very long-distance transport

STANDARD CHANGING INTERVAL

This is the symbol for the standard changing
interval. See ”Fluids and lubricants”
specifications manual for prescribed oil
specification.

G000089

EXTENDED CHANGING INTERVAL

This is the extended changing interval symbol.

If the prescribed oil specification and any
additional conditions (see specification manual
”Fluids and lubricants”) have to be complied
with, an extended changing interval may be
applied.

Note:

An extended engine oil changing interval is not
allowed for the VF and XE engines.

G000077



200424

Содержание 95XF





























































































































































































Результаты поиска

Содержание 95XF

Отзывы:

Похожие инструкции для 95XF

Бренды по названию

Популярные бренды

DAF 95XF, Руководство по обслуживанию

Результаты поиска

Содержание 95XF

Отзывы:

Похожие инструкции для 95XF

Бренды по названию

Популярные бренды