DAF 95XF Скачать руководство пользователя страница 146

Страница: 146 / 188

EXPLANATORY NOTES ON THE MAINTENANCE ACTIVITIES

Removal and installation

series

4-26

3 4

5 6

11 12

S7 00 401

Installing the wheel hub

Check the wheel hub and the wheel
bearings for wear and damage, see
“Inspection and adjustment”.

Fit a new wheel speed sensor ring (10) to
the hub, if necessary.

Fit new wheel bearings into the hub, if
necessary.

Blow-dry the wheel bearings (7) and (13)
using compressed air.

Fill the wheel bearings with the specified
wheel bearing grease.
Also apply a layer of grease to the wheel
bearing circumference.

Fit the wheel bearing (13) into the hub (9).

Fill the inside circumference of the hub with
wheel bearing grease.

Fit a new hub seal (14) in the hub (9).

Apply a little grease to the sealing lips of the
seal (14).

10. Check that the wheel speed sensor (11) is

correctly clamped in the stub axle. Replace
the clamping sleeve of the sensor, if
necessary.

11. Position the wheel in front of the axle

journal using the tyre lift.
Fit the outer wheel bearing (7) into the hub
so that the outer wheel bearing can also
serve as a guide when installing the hub.

S7 00 140



200424

Содержание 95XF





























































































































































































Результаты поиска

Содержание 95XF

Отзывы:

Похожие инструкции для 95XF

Бренды по названию

Популярные бренды

DAF 95XF, Руководство по обслуживанию

Результаты поиска

Содержание 95XF

Отзывы:

Похожие инструкции для 95XF

Бренды по названию

Популярные бренды