Daewoo Q600 series Скачать руководство пользователя страница 2

Страница: 2 / 112

This indicates that minor to
moderate injuries may occur
as a result of not observing
this warning.

Caution

This indicates that death or
Serious injuries may occur
As a result of not observing
this warning.

◆ Please read [Cautions for Safety] carefully in advance and use the refrigerator correctly.

Warning

◆ Meaning of marking

Don’t Disassemble.

Disconnect the power plug.

Prohibited / Don’t try to do it.

Enforced / You should observe

instructions.

For your safety, please observe following items

Warning

When connecting the power
plug, make sure it is fastened
certainly.

◇ Electrical insulation will be
weakened and causing electric
shock or fire outbreak.

Do not install refrigerator in humid
environments.

◇ If electrical insulation were
weakened, it would cause electric
shock or fire outbreak.

When inserting the power plug,
the direction of the electrical cord
is downward.
◇ When the direction of cord is

inserted upward, it may be

damaged and causing short circuit
and overheat. then electric shock
or fire outbreak may occur.

When you feel a combustible gas
leaking, air the area so that
the refrigerator does not exposed
to gas.
◇ A spark at an electrical contact
point may cause an explosion, fire
or burning damage.

When the power cord is damaged,
please make a call for a service.

◇ It may cause fire outbreak,
electric shock or short circuit.

Before disposing of refrigerator,
remove the rubber packing of
the doors.
◇ Children can lock themselves
in the refrigerator and may be
suffocated.

1. Safety Warnings & Cautions

Содержание Q600 series

















































































































Результаты поиска

Содержание Q600 series

Отзывы:

Похожие инструкции для Q600 series

Бренды по названию

Популярные бренды

Daewoo Q600 series, Руководство по обслуживанию

Результаты поиска

Содержание Q600 series

Отзывы:

Похожие инструкции для Q600 series

Бренды по названию

Популярные бренды