background image

MNL-00024 [1] 

Proprietary and Confidential  

Page 

6

 of 

21 

 

5.0

 

Transport and Storage Specifications 

Ambient Temperature: 

-40°C to 70°C  (-40°F to 158°F) 

Relative Humidity: 

10% to 95%, Non-condensing  

Atmospheric  Pressure: 

50 kPa to 106 kPa 

Altitude: 

≤ 2000m

 

 

6.0

 

EMC Precautions 

The devices contained in this manual have been tested and found to comply with the EMC limits of the 
international standard IEC 60601-1-2.  These limits are designed to provide reasonable protection 
against interference in a typical medical installation.  The system can radiate radio frequency energy if 
not installed in accordance with the instructions, and may cause harmful interference to other devices in 
the vicinity.  There is no guarantee that interference will not occur in a particular installation.  If the 
system does cause interference with other devices, which can be determined by turning the system off 
and on, the user is encouraged to try to correct the interference by one or more of the following 
measures: 

 

Re-orient or relocate the receiving device 

 

Increase the separation between the equipment 

 

Connect the System into an outlet on a circuit different from that to which the other device(s) is 
connected 

Consult the manufacturer or field service technician for help 
 

7.0

 

Electrical Specifications 

The device is manufactured in the following electrical configurations.  Always refer to the identification 
label of the device to determine which electrical configuration the device is manufactured to. 
 

 

Mains input = 230V, 3~, 60Hz, 100A   Operating = 230V, 3~, phase to phase  

 

Mains input = 400V, 3N~, 50Hz, 100A   Operating = 230V~, single-phase (phase to neutral) 

 

8.0

 

Site Selection 

A site should be chosen within reach of the specified electrical connection (refer to the Facility 
Requirements Guide) and where the unit can be left in place without obstructing traffic flow. It is 
important that the unit be properly grounded. The site should not be in any area where water or 
moisture might collect and should be protected from access by children and other unintended users.  

WARNING: 

To avoid the risk of electric shock this equipment must only be connected to a supply mains 

with a protective earth.  

CAUTION:

 This device is a Class A Medical Device suitable for use in all establishments other than 

domestic and those directly connected to the public low voltage power supply network that supplies 
buildings used for domestic purposes. 

Содержание ML24000






















Отзывы: