D-Link DSL-2540T Скачать руководство пользователя страница 45

Страница: 45 / 112

DSL-2540T ADSL Router User Guide

SCR

Sustainable Cell Rate – The SCR is defined for the VBR service category.

This is the rate that can be sustained for “bursty”, on-off traffic sources. It

is a function of Maximum Burst Size (MBS) and the time interval (between
cells).

CDVT

Cell Delay Variation Tolerance – CDVT is a measure of the cell clumping
phenomenon by which cells are delayed in the network and are

clumped together and arrive at a system at a faster rate than negotiated.

Increasing the CDVT creates greater bucket depth.

MBS

Maximum Burst Size – The MBS is the maximum number of bytes that can

be sent continuously from the source to the destination dropping any

packets. Some ATM providers set the MBS and CDVT very low and adjust
up if problems occur.

Содержание DSL-2540T

















































































































Результаты поиска

Содержание DSL-2540T

Отзывы:

Похожие инструкции для DSL-2540T

Бренды по названию

Популярные бренды

D-Link DSL-2540T, Руководство пользователя

Результаты поиска

Содержание DSL-2540T

Отзывы:

Похожие инструкции для DSL-2540T

Бренды по названию

Популярные бренды