D-Link DGS-3224SR Скачать руководство пользователя страница 71

Страница: 71 / 282

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

create snmp host

packets have not been tampered
with in transit.

•

Authentication

−

determines that an

SNMP message is from a valid
source.

•

Encryption

−

scrambles the

contents of messages to prevent it
being seen by an unauthorized
source.

noauth_nopriv

−

Specifies that there

will be no authorization and no
encryption of packets sent between the
switch and a remote SNMP manager.

auth_nopriv

−

Specifies that

authorization will be required, but
there will be no encryption of packets
sent between the switch and a remote
SNMP manager.

auth_priv

−

Specifies that

authorization will be required, and
that packets sent between the swtich
and a remote SNMP manger will be
encrypted.

<auth_sting 32>

−

An alphanumeric

string used to authorize a remote
SNMP manager to access the switch’s
SNMP agent.

Restrictions

Only administrator-level users can issue
this command.

Содержание DGS-3224SR



























































































































































































































































































Результаты поиска

Содержание DGS-3224SR

Отзывы:

D-Link DGS-3224SR, Справочное руководство по интерфейсу командной строки, Страница: 71 / 282

Результаты поиска

Содержание DGS-3224SR

Отзывы: