D-Link DGS-3224SR Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 282

D-Link DGS-3224SR Скачать руководство пользователя страница 114

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

114

To set the path cost 19, the priority 16, and the state
enabled of the ports 1-5:

DGS-3224SR:4#config stp ports 1:1-1:5 cost 19 priority
16 state enabled
Command: config stp ports 1:1-1:5 cost 19 priority 16
state enabled

Success.

DGS-3224SR:4#

enable stp

Purpose

Used to globally enable STP on the switch.

Syntax enable

stp

Description

This command allows the Spanning Tree
Protocol to be globally enabled on the
switch.

Parameters none.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To enable STP on the switch:

DGS-3224SR:4#enable stp
Command: enable stp

Success.

«
...
112
113
114
115
116
...
»

Содержание DGS-3224SR



























































































































































































































































































Отзывы:

Нет отзывов