D-Link DGS-3224SR Скачать руководство пользователя страница 174

Страница: 174 / 282

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

174

INK

GGREGATION

OMMANDS

The link aggregation commands in the Command Line Interface
(CLI) are listed (along with the appropriate parameters) in the
following table.

Command Parameters

create
link_aggregation

{group_id <value> {type [lacp | static]}

delete
link_aggregation

group_id <value>

config
link_aggregation

group_id <value> {master_port <port> |
ports <portlist> | state [enabled|disabled]

config
link_aggregation
algorithm

show
link_aggregation

{group_id <value> | algorithm}

Config lacp_port

<portlist> mode(1) [active(3) | passive(4)

Show lacp_port

{<portlist>}

Each command is listed, in detail, in the following sections.

Содержание DGS-3224SR



























































































































































































































































































Результаты поиска

Содержание DGS-3224SR

Отзывы:

Бренды по названию

Популярные бренды

D-Link DGS-3224SR, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DGS-3224SR

Отзывы:

Бренды по названию

Популярные бренды