D-Link DGS-3224SR Скачать руководство пользователя страница 267

Страница: 267 / 282

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

267

config time_zone

Purpose

Used to configure the time zone on the
switch.

Syntax

config time_zone {operator [+|-] hour <

gmt_hour 0-13> | min <minute 0-59>}

Description

This command will set the time zone for the
switch.

Parameters

operator – signals addition or subtraction
to follow

+ - add

- - subtract

gmt_hour – number of hours to or from
Greenwich Mean Time (GMT)

min – number of minutes

Restrictions

Administrator privileges are needed to
issue this command.

Example Usage:

To set the time zone on the switch for Taipei:

Содержание DGS-3224SR



























































































































































































































































































Результаты поиска

Содержание DGS-3224SR

Отзывы:

Бренды по названию

Популярные бренды

D-Link DGS-3224SR, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DGS-3224SR

Отзывы:

Бренды по названию

Популярные бренды