D-Link DGS-3224SR Скачать руководство пользователя страница 256

Страница: 256 / 282

DGS-3224SR Stackable Gigabit Ethernet Switch User’s Guide

256

create iproute default

−

The IP address for the next hop

router.

−

The default setting is

Restrictions

Administrator privileges are needed to
issue this command.

Usage Example:

To create an IP route for the routing table:

DGS-3224SR:4#create iproute default 10.52.19.2
Command: create iproute default 10.52.19.2

Success.

DGS-3224SR:4#

delete iproute default

Purpose

Used to delete an IP route entry from the
switch’s IP routing table.

Syntax

delete iproute default

Description

This command will delete an existing entry
from the switch’s IP routing table.

Parameters

default

−

deletes a default IP route entry.

Содержание DGS-3224SR



























































































































































































































































































Результаты поиска

Содержание DGS-3224SR

Отзывы:

D-Link DGS-3224SR, Справочное руководство по интерфейсу командной строки, Страница: 256 / 282

Результаты поиска

Содержание DGS-3224SR

Отзывы: