D-Link DGS-2000 Series Скачать руководство пользователя страница 84

Страница: 84 / 144

4 Web-based Switch Configuration

D-Link DGS-2000 Series Ethernet Switch User Manual

Figure 4.101 - Configuration > Multicast Forwarding & Filter > Multicast Forwarding

VID

: Specify the VID

Multicast MAC Address

: Specify the multicast address.

Egress

: Click the Port Number for multicast traffic.

Configuration > Multicast Forwarding & Filtering > Multicast Filter Mode

The Multicast Filtering Mode page allows user to set up the filtering mode.

Figure 4.102 - Configuration > Multicast Forwarding & Filtering > Multicast Filtering

From Port / To Port:

Specify the ports of the VLAN on which the corresponding MAC address belongs to.

Multicast Filtering Mode:

This drop-down menu allows user to select the action the Switch will take when it

receives a multicast packet that is to be forwarded to one of the ports in the range specified above.

Forward Unregistered Groups -

This will instruct the Switch to forward a multicast packet whose

destination is an unregistered multicast group residing within the range of ports specified above.

Filter Unregistered Groups -

This will instruct the Switch to filter any multicast packets whose

destination is an unregistered multicast group residing within the range of ports specified above.

Configuration > Multicast Forwarding & Filtering > IP Multicast Profile Settings

The IP Multicast Profile Settings page allows user to configure the IP Multicast Profile.

Figure 4.103 - Configuration > IGMP Snooping > IP Multicast Profile Settings

Содержание DGS-2000 Series

















































































































































Результаты поиска

Содержание DGS-2000 Series

Отзывы:

Бренды по названию

Популярные бренды

D-Link DGS-2000 Series, Справочное руководство

Результаты поиска

Содержание DGS-2000 Series

Отзывы:

Бренды по названию

Популярные бренды