D-Link DGS-2000 Series Скачать руководство пользователя страница 40

Страница: 40 / 144

4 Web-based Switch Configuration

D-Link DGS-2000 Series Ethernet Switch User Manual

Figure 4.21 – System > IP Interface Settings

Interface Name:

Specifies the name of IP interface.

VLAN Name:

Specifies the VLAN name of IP interface.

IPv4 Address:

Specifies the IPv4 address for the interface.

Netmask:

Select the netmask of IP address.

Interface Admin State:

Enables or disables the interface administration state.

System > IPv6 Setting > IPv6 System Settings

Used to configure IPv6 parameters for system interface.

Figure 4.22 – System > IPv6 Interface Settings

IPv6

: Options to

enable

disable

IPv6 address of system interface.

DHCPv6 Client

: Options to

enable

disable

DHCPv6 client mode on system interface.

NS Retransmit Time Settings

: Specify the time period for sending NS.

Automatic Link Local State Setting

: Options to

enable

disable

Link Local address of system interface.

System > IPv6 Setting > IPv6 Neighbor Settings

Figure 4.23 – System > IPv6 Neighbor Settings

Содержание DGS-2000 Series

















































































































































Результаты поиска

Содержание DGS-2000 Series

Отзывы:

Бренды по названию

Популярные бренды

D-Link DGS-2000 Series, Справочное руководство

Результаты поиска

Содержание DGS-2000 Series

Отзывы:

Бренды по названию

Популярные бренды