manualshive.com logo in svg

D-Link DGS-2000 Series, Справочное руководство

Поделиться
Скачать
D-Link DGS-2000 Series Скачать руководство пользователя страница 64

4  Web-based Switch Configuration

  

D-Link DGS-2000 Series Ethernet Switch User Manual 

5

5

7

7

 

 

 

Figure 4.68– Configuration > IGMP Snooping > IGMP Snooping-Multicast Entry Table 

 

Configuration > IGMP Snooping > IGMP Access Control Settings 

The IGMP Access Control Settings page is used to enable or disable the IGMP access control of selected 

ports.  

 

Figure 4.69 – Configuration > IGMP Snooping > IGMP Access Control Settings 

 

From Port/To Port: 

Select the port ranges to be configured. 

Status:

 Enable or disable the IGMP Access Control of specified ports. 

 
Click 

Apply

 to make the configurations take effect. 

 

Configuration > IGMP Snooping > Host Table 

The Host Table page displays the information of Host Table. Including VLAN ID, Group, Port Number and 

Host IP. 

 

Figure 4.70 - Configuration > IGMP Snooping > Host Table 

 

Configuration > IGMP Snooping > IGMP Snooping Static Group Settings 

The IGMP Snooping Static Group Settings page allows the Switch to read the Multicast Group IP address 

and the corresponding MAC address from IGMP packets that pass through the Switch. 

 

Figure 4.71- Configuration > IGMP Snooping > IGMP Snooping Static Group Settings 

 

VLAN Name: 

Specifies the VLAN name of the multicast group. 

VID List: 

Specifies the VID list or of the multicast group. 

IPv4 Address: 

Specifies the IPv4 address. 

 

Содержание DGS-2000 Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды