D-Link DGS-2000 Series Скачать руководство пользователя страница 112

Страница: 112 / 144

4 Web-based Switch Configuration

D-Link DGS-2000 Series Ethernet Switch User Manual

UnderSize:

The number of packets detected that are less that the minimum permitted packets size of

bytes and have a good CRC. Undersize packets usually indicate collision fragments, a normal network

occurrence.

OverSize:

Counts packets received that were longer that

1518

octets, or if a VLAN frame is

1522

octets, and

less that the MAX_PKT_LEN. Internally, MAX_PKT_LEN is equal to

1522

Fragment:

The number of packets less than

bytes with either bad framing or an invalid CRC. These are

normally the result of collisions.

Jabber:

The number of packets with lengths more than the MAX_PKT_LEN bytes. Internally,

MAX_PKT_LEN is equal to

1522

Drop:

The number of packets that are dropped by this port since the last Switch reboot.

Show/Hide:

Check whether or not to display CRC Error, Under Size, Over Size, Fragment, Jabber, and

Drop errors.

Clear:

Clicking this button clears all statistics counters on this window.

View Table:

Clicking this button instructs the Switch to display a table rather than a line graph.

View Line Chart:

Clicking this button instructs the Switch to display a line graph rather than a table.

Monitoring > Errors > Transmitted (TX)

This page displays the following graph of error packets transmitted on the Switch. To select a port to view

these statistics for, select the port by using the

Port

pull-down menu. The user may also use the real-time

graphic of the Switch at the top of the web page by simply clicking on a port.

Figure 4.156 - Monitoring > Errors > Transmitted (TX) (line graph)

To view the

Transmitted Error Packets Table

, click the link

View Table

, which will show the following table:

Figure 4.157 - Monitoring > Errors > Transmitted (TX) (table)

The following fields can be set or viewed:

Time Interval:

Select the desired setting between

and

60s

, where “s” stands for seconds. The default

value is

one

second.

Record Number:

Select number of times the Switch will be polled between

and

200

. The default value is

200

Содержание DGS-2000 Series

















































































































































Результаты поиска

Содержание DGS-2000 Series

Отзывы:

Бренды по названию

Популярные бренды

D-Link DGS-2000 Series, Справочное руководство

Результаты поиска

Содержание DGS-2000 Series

Отзывы:

Бренды по названию

Популярные бренды