CYBEX Arc Trainer 600A Скачать руководство пользователя страница 82

Страница: 82 / 107

Cybex Arc Trainer Owner’s & Service Manual

Page 7-26

Using a 3/16” hex key, attach each connecting rod with a screw removed in step 3A.
See Figure 4.

21. Attach the access cover.

While being sure not to pinch any cables, place the access cover in position.

Using a Phillips head screwdriver, attach the four screws removed in step 2A. See
Figure 2.

22. Test the unit for proper operation.

Connect the power cord into the power outlet.

Turn the main power switch above the power inlet to the on (I) position.

Operate the unit at all levels to verify proper operation.

Lower Pillow Blocks

Tools Required

• Phillips head screwdriver
• 3/16” Hex key
• 1/8” Hex key
• 2.5” (6.3 cm) Wooden block
• 9/16” Socket wrench
• 9/16” Open end wrench

! WARNING: Disconnect the power cord before beginning this procedure. Keep wet

items away from inside parts of the unit. Electrical shock could occur even
if the unit is unplugged.

Elevate the unit and disconnect the power source.

Plug the power cord into the power outlet.

Enter

Test Mode

Elevate the unit to a minimum of level 7 incline.

While the unit is elevated, turn the main power switch to the off (O) position and
unplug the power cord from the power outlet.

Remove the access cover.

Using a Phillips head screwdriver, remove the four screws securing the access cover.
See Figure 2.

Remove the access cover.

! WARNING: Flywheel may be hot. Wait until it cools before servicing.

Содержание Arc Trainer 600A












































































































Результаты поиска

Содержание Arc Trainer 600A

Отзывы:

Похожие инструкции для Arc Trainer 600A

Бренды по названию

Популярные бренды

CYBEX Arc Trainer 600A, Руководство по эксплуатации для владельца

Результаты поиска

Содержание Arc Trainer 600A

Отзывы:

Похожие инструкции для Arc Trainer 600A

Бренды по названию

Популярные бренды