manualshive.com logo in svg

CYBEX Arc Trainer 600A, Руководство по эксплуатации для владельца

Поделиться
Скачать
CYBEX Arc Trainer 600A Скачать руководство пользователя страница 81

Cybex Arc Trainer Owner’s & Service Manual

Page 7-25

Table of Contents

. . . . . . . . .  iii

7 Service

Warnings/Cautions  . . . . . . .  7-1
Test Mode . . . . . . . . . . . . . .  7-2
LED Functions . . . . . . . . . . .  7-3
Key Functions . . . . . . . . . . .  7-3
Error Codes . . . . . . . . . . . . .  7-4
Speed Sensor Adjustment .  7-5
Drive Belts . . . . . . . . . . . . . .  7-7
Eddy Current Brake. . . . . .  7-13
Elevation Motor . . . . . . . . .  7-16
Power Switch . . . . . . . . . .  7-20
Upper Pillow Blocks . . . . . . 7-22
Lower Pillow Blocks  . . . . . 7-26
Pedal Arm & Linkage Arm  . 7-28
Lower Control Board . . . . .  7-29
Upper Display Board . . . . .  7-31
Contact Heart Rate Board.  7-33
CSAFE Board . . . . . . . . . .  7-35
Upper Display Cable . . . . .  7-36
Lower Display Cable . . . . .  7-38
Display Overlays . . . . . . . .  7-41
Parts List . . . . . . . . . . . . . .  7-43
Exploded Views. . . . . . . . .  7-45
Schematic . . . . . . . . . . . . .  7-51

E.

Using a 1/8” hex key, tighten the two set screws on each pillow block.

! CAUTION: Do not pinch your fingers between the belt and pulley during

this procedure. 

14. Secure the crank arms.

A.

Slide each crank arm in place. 

NOTE: 

The face of each crank arm

should be flush with the end of each shaft.

B.

Using a 7/16” socket wrench, tighten the one screw on each crank arm.

15. Attach the lower board assembly.

A.

Place the lower board assembly over the two bottom screws and slide it
to the right. 

B.

Using a Phillips head screwdriver, attach the top two screws removed in
step 8D and tighten the bottom two screws.

C.

Connect the elevation cable to the lower board and slide it into its slot
on the frame. 

D.

Place the washer (first) and the ground terminal (next) onto the stud and
tighten with the nut removed during step 8C. 

E.

Place the lower board shield in position and snap it in. 

16. Attach the crank arm disk supports.

A.

Using a Phillips head screwdriver, attach each crank arm disk support
with one screw removed during step 7A. See Figure 20. 

17. Tension the drive belt.

A.

Using a 7/16” socket wrench, tighten the two screws on the lower pivot
shaft. See Figure 15. 

18. Attach the crank covers. 

A.

Place each crank cover in position.

B.

Using a Phillips head screwdriver, attach each crank cover with three
screws removed in step 5A. See Figure 6.

19. Secure the side covers.

A.

Place the two side covers and gasket in position.

B.

Using a Phillips head screwdriver, attach each side cover with the six
screws and six washers removed in step 4A. 

20. Attach the connecting rods.

A.

Place each connecting rod in position.

Содержание Arc Trainer 600A












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды