manualshive.com logo in svg

CWSI CP-3000, Руководство по эксплуатации и установке

Поделиться
Скачать
CWSI CP-3000 Скачать руководство пользователя страница 9

 

9

 

2.2 Compatibility  

The following UL Listed RF devices are compatible with the CP-3000Control Panel: 
Commercial Wireless Systems International, LLC

 

A/C Repeater Model AR-3 – A/C powered repeater 
Battery Repeater Model BR-3 – Battery powered Repeater 
Smoke Detector Model 300 – Photo Electric Smoke Detector with Integral Sounder 
Manual Pull Station Model 310 – Non Coded Fire Alarm Box 
Heat Detectors models 320/321 – Automatic Fixed and Rate of Rise Heat Detector 
Fire Transmitter Model 330 – N.O. EOL Supervised Transmitter  

The following antennas are for use with the CP-3000: 
Commercial Wireless Systems International, LLC

 

Models: 
OM-1 Omni, OM-2 Omni, YA-1 Yagi, YA-2 Yagi  

The following UL Listed Digital communicators are compatible with the CP-3000 Control 
Panel: 
Communicators are to be determined. They will be activated via dry contact relay outputs                     

Содержание CP-3000





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды