1. INSTALLATION AND USE
KPM216H
5
1-
•
USB Address Number :
0
D
, 1, 2, 3, 4, 5, 6, 7, 8, 9.
•
USB Status Monitor
(3)
:
Disabled
D
or Enabled.
•
Autofeed:
CR disabled
D
or CR enabled.
•
Print mode:
Normal
D
or Reverse.
•
Characters per inch:
204 dpi version
:
A=11 B=15 cpi
D
, A=15 B=20 cpi.
300 dpi version
:
A=16 B=23 cpi
D
, A=23 B=30 cpi.
•
Speed/Quality:
High Quality, Normal
D
, High Speed.
•
Automatic Ejecting
(4)
:
Disabled
D
, Enabled T.out 5 sec, Enabled T.out 10 sec,
Enabled T.out 15 sec, Enabled T.out 20 sec, Enabled T.out 30 sec,
Enabled T.out 40 sec, Enabled T.out 60 sec, Enabled T.out 2 min.
•
Paper retract
(5)
:
Disabled
D
, Enabled No Timeout, Enabled T.out 5 sec, Enabled
T.out 10 sec, Enabled T.out 15 sec, Enabled T.out 20 sec, Enabled T.out 30
sec, Enabled T.out 40 sec, Enabled T.out 60 sec, Enabled T.out 2 min.
•
Dot Damage Prevention
(6)
:
Disabled
D
, ± 7 dot o ± 15 dot.
•
Notch Alignment :
Disabled
D
or Enabled.
•
Notch Threshold
(7)
:
0.5 V, 1.0 V, 1.5 V, 2.0 V, 2.5 V, 3.0 V, 3.5 V
D
, 4.0 V, 4.5V.
•
Notch Distance [mm]
(8)
:
0
D
.
•
Short ticket (< 150mm)
(9)
:
Disabled
D
or Enabled.
•
Print density:
-50%, -37%, -25%, -12%, 0%
D
, +12%, +25%, +37%, +50%.
Please note: the parameters marked with the symbol
D
represent the default values.
(2)
N.B.
:
parameter valid only wth serial interface; using this parameter, it is
possible to select whether the Busy signal is activated when the printer is both in
Off Line status and the buffer is full, or only if the reception buffer is full.
(3)
N.B.
:
This parameter is displayed if the printer has an USB interface. The
Status Monitor is an additional printing driver component that allows the printer
status monitoring.
(4)
N.B.
:
If paper is present on the ejector and if this parameter is desabled,
the printer can’t perform the paper retract; if this parameter has been
activated in “No Timeout” mode, when the printer receives the command, it
can retract the paper; if this parameter has been activated in “T.out 5-10-15-
20-30-40- 60 sec-2 min” mode, the printer executes automatically the paper
retract after 20-30-40-60 seconds or 2 minutes.
(5)
N.B.
:
if this parameter is desabled, the printer can’t perform the automatic
ejecting; if this parameter has been activated in “T.out 5-10-15-20-30-40-60
sec-2 min” mode, the printer executes automatically the automatic ejecting
after 20-30-40-60 seconds or 2 minutes.
(5)
N.B.
:
Function, if enabled, allows to prevent the deterioration of dots
stressed with special print-outs like graphics, tables and similar.
(7)
N.B.
:
The parameter “Notch distance” is displayed and enabled only in
case that the notch alignment parameter is enabled. The parameter “Notch
distance” is used to set the exact distance of the notch entering the
desired value in millimetre and in deci-millimetre.
(8)
N.B.
:
Function, if enabled, allows to print ticket more short than 150mm
(see the paragraph 4.1 technical specifications).
Содержание KPM 216 H
