CUMMINS ALLISON JetScan MPX 8200 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 28

background image

14 |

JetScan

®

MPX 8200 strapping and corner module

| Configuring strap length and printing

8. The value under Characters Remaining on the bottom right side of the screen

indicates character-limit status.

If the number is positive and highlighted in green, additional characters can be

used.

If the number is negative and highlighted in red, the 40-character limit is exceeded.

If the combined settings are not reduced to 40 characters or less, the Text (custom
message) is cut off after the 40th character.

To bring the combined number of characters below the 40-character limit, do one or

both of the following:

• Reduce the length of the Text (custom message). Press

Customize

and use the

backspace key

to change the message.

• Disable the Date, Time or Operator ID.

9. When configuration is complete:

a. Press

Save

, followed by

OK

to prompt the

Processing Type Setup

tab /

Settings

screen.

b. Press the

Exit Setup

tab to prompt the

Menu

tab screen.

c. Press the

Processing

tab to prompt the main-processing screen.

«
...
12
13
14
15
16
...
»

Содержание JetScan MPX 8200





























Отзывы:

Нет отзывов

Похожие инструкции для JetScan MPX 8200

Бренд: Waterwise Страницы: 12

Бренд: ParaBody Страницы: 38

Бренд: NORLUX Страницы: 2

Бренд: VeEX Страницы: 2

Бренд: JB-Lighting Страницы: 48

Бренд: Handler Страницы: 25

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: Lafayette Страницы: 10

Бренд: WARPP Страницы: 28

Бренд: Safco Страницы: 2

C-HB-A-LB2-SCCT Series

Бренд: C-LITE Страницы: 9

X-431 Torque HD

Бренд: Launch Страницы: 3

GPSMAP 9 3 Series

Бренд: Garmin Страницы: 222

ARCHISHAPE 2.0 Linear

Бренд: Osram Страницы: 7

Alcotest 7410 GLC

Бренд: Dräger Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды