CUMMINS ALLISON JetScan MPX 8200 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 28

CUMMINS ALLISON JetScan MPX 8200 Скачать руководство пользователя страница 7

Maintaining bins |

JetScan

®

MPX 8200 strapping and corner module

| 7

Maintaining bins

Empty the strapped-note collection bin when:

• One bin is full.

• Two bins are full, and the machine stops processing. Empty both collection bins to

continue operation.

To empty a full bin:

1. Locate the full bin:

• The

Alert: Strapper bin limit reached!

screen identifies a full bin in green, as

shown below.

• A green light also illuminates on the top of the bin that is full.

2. Remove the full bin and empty its contents. The top

of any strapping module can be used as a work
surface.

3. Return the empty bin to the strapping module.

A warning message appears on the main-
processing screen if the empty bin is not
completely inserted into the strapping module.

4. Press

OK

on the

Alert: Strapper bin limit reached!

screen.

OK

may be pressed

before or after any full bin is removed and emptied.

2

4

«
...
5
6
7
8
9
...
»

Содержание JetScan MPX 8200





























Отзывы:

Нет отзывов