CUMMINS ALLISON JetScan MPX 8200 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 28

CUMMINS ALLISON JetScan MPX 8200 Скачать руководство пользователя страница 8

8 |

JetScan

®

MPX 8200 strapping and corner module

| Maintaining paper rolls

Maintaining paper rolls

To remove an existing paper roll or an empty paper-roll core from a strapping module:

1. Open the upper-front access door and lower paper-roll access door.

Burn hazard. Hot surface below strap head.
Do not touch.
See the

section for more information.

2. Disengage the loose end of the

strapping paper from the strap head by
doing one of the following:

a. Turning the top, small feed roller

counter-clockwise.

b. Turning the bottom, large feed roller

clockwise.

3. Gently pull the vertical section of

strapping paper along the inside, right
wall of the cabinet so it is completely
free of all guides.

4. Wind the paper roll in a counter-

clockwise direction, until the paper is
free from the paper path and
completely wound around the paper
roll, as shown at right.

5. Pull the paper roll or empty core off

the paper-roll shaft.

6. Set the paper roll aside or discard the

empty core.

To load a new paper roll on a strapping

module:

1. Open the upper-front access door and

lower paper-roll access door.

2. Firmly push the paper-roll core onto

the paper-roll shaft until it stops,
making sure it is inserted so the paper
unwinds in the clockwise direction.

2a

4

2b

Strap

head

2

«
...
6
7
8
9
10
...
»

Содержание JetScan MPX 8200





























Отзывы:

Нет отзывов