Cubic COM5000-8 Скачать руководство пользователя страница 21

Страница: 21 / 66

351804-1 Rev. 100

COM5000-8 TECHNICAL MANUAL

CHAPTER 3

OPERATION

3.1.

INTRODUCTION

This section describes the controls and indicators available to the operator. Basic operation of the Power
Amplifier is also described. For a description of the exciter controls and display refer to the T-4180 manual.

3.2

CONTROLS AND DISPLAYS

The controls and indicators are located on the Front Panels of the following modules:

Power Supply Module
PA Module (4 each)
System Controller Module

T-4180 Exciter module (refer to the T-4180 manual)

3.2.1

Power Supply Module

Figure 3.2.1 shows the Power Supply Module Front Panel. The controls and indicators are described below:

Control/Indicator

Function

AC ON (PS#1) LED (yellow)

When lit, indicates that internal power supply invertor #1 is on and
operating normally.

AC ON (PS#2) LED (yellow)

When lit, indicates that internal power supply invertor #2 is on and
operating normally.

AC ON (PS#3) LED (yellow)

When lit, indicates that internal power supply invertor #3 is on and
operating normally.

DC ON LED (green)

When lit, indicates that the DC output of the power supply is on.

3-Pole Toggle Circuit Breaker

Connects and disconnects the AC input to the power supply.

Push-Pull Circuit Breakers (8)

Connects and disconnects the DC outputs to individual PA modules.
There are 2 circuit breakers per PA module.

Содержание COM5000-8



































































Результаты поиска

Содержание COM5000-8

Отзывы:

Похожие инструкции для COM5000-8

Бренды по названию

Популярные бренды

Cubic COM5000-8, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание COM5000-8

Отзывы:

Похожие инструкции для COM5000-8

Бренды по названию

Популярные бренды