Cubic COM5000-8 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 66

background image

351804-1 Rev. 100

COM5000-8 TECHNICAL MANUAL

10

2.1.4.4

External Connections to the Transmitter

All connections are routed through the cable entry brush strip located below the rear door.

AC LINE Input Connection

The External AC Line power cable connects to the terminal block inside a junction box at the bottom inside
floor of the cabinet. The recommended minimum wire size is #6 AWG (16mm

2

). The terminals will accept up

to #4 AWG (25mm

2

) wire.

The connections are labeled near the terminals:

L1:

Line 1 (black)

L2:

Line 2 (red)

L3:

Line 3 (blue)

: Ground (green)

Note: Phase is not critical. Any AC line phase may be connected to any line terminal.

The power requirement is 3-phase/4-wires (3 lines and ground), 187

– 240 VAC, 47-63Hz.

The maximum AC input current is 50A/phase.

Antenna Connection

The antenna cable is connected to the LC connector located at the inside rear of the cabinet.

Remote Control Interface

Remote control of the transmitter is provided via an RS-232/RS-422 interface on the rear of the T-4180
exciter at J4. See the T-4180 manual for details.

Audio Connection

Two balanced 600 ohm audio inputs are provided on J6 of the Exciter rear panel. A microphone input with
PTT (push to talk) is also available on the front panel of the exciter. See the T-4180 manual for details.

External Reference

An external 10 MHz reference input is provided on J2 of the Exciter rear panel. See the T-4180 manual for
details.

Cabinet Ground Connection

An M6 (

≈

¼”) ground stud is located inside the lower rear of the rack cabinet (right side as viewed from the

rear) to provide connection to safety ground wiring.

CAUTION:

BEFORE OPERATING THE TRANSMITTER FOR THE FIRST TIME AFTER INSTALLATION

IS COMPLETE, DOUBLE CHECK THAT ALL CABLES ARE CORRECTLY INSTALLED.

SEVERE DAMAGE TO THE TRANSMITTER CAN OCCUR IF CABLES ARE NOT

CONNECTED OR ARE CONNECTED IMPROPERLY! IT IS HIGHLY RECOMMENDED THAT

INITIALLY TESTING BE DONE WITH THE POWER SET TO 10%. IF THE TRANSMITTER IS

OPERATING NORMALLY AT 10% POWER, THE POWER MAY BE GRADUALLY

INCREASED TO 100%. THIS PRECAUTION IS ALSO RECOMMENDED ANY TIME A

MODULE IS REPLACED.

«
...
18
19
20
21
22
...
»

Содержание COM5000-8



































































Отзывы:

Нет отзывов

Похожие инструкции для COM5000-8

Бренд: Panasonic Страницы: 3

Бренд: CABASSE Страницы: 2

Бренд: D.A.S. Страницы: 28

Бренд: d&b audiotechnik Страницы: 28

Бренд: Hamilton/Buhl Страницы: 16

Бренд: Hamilton Electronics Страницы: 5

Бренд: Yaesu Страницы: 17

Бренд: S.M.S.L Страницы: 32

Бренд: Teac Страницы: 15

Бренд: SMSL Страницы: 28

Power Amplifier Servo 120

Бренд: Samson Страницы: 13

Nova PA-600 Operation manual

Бренд: EarthQuake Страницы: 12

Бренд: Ayre Страницы: 24

Бренд: lb Страницы: 16

Бренд: Ecler Страницы: 9

Бренд: Phoenix Gold Страницы: 12

Бренд: Fishman Страницы: 16

Бренд: ATI Audio Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды