Cubic COM5000-8 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 66

background image

351804-1 Rev. 100

COM5000-8 TECHNICAL MANUAL

17

STDBY mode:

The Transmitter enters STDBY mode if the System Controller, the T-4180 and the 50VDC Power Supply
module is turned ON. Serial data communication must also have been established between the T-4180 and
the System Controller to enter STDBY mode. The transmitter remains in STDBY mode under certain fault
conditions.

OPER mode:

If the System Controller, the T-4180 and the 50VDC Power Supply modules are turned ON and serial data
communication has been established between the T-4180 and the System Controller, the OPER LED
indicator is lit.

Note:

The following conditions will prevent the Transmitter from entering OPER status (the
Transmitter will remain in STDBY mode):

a.

Operational Interlock (Cabinet rear door Interlock) disabled

b.

One or more Drawer Interlocks are disabled

c.

A serious fault condition

Note:

The Transmitter may enter the OPER status even if faults have been detected. Operation is
permitted

– at reduced power – under many fault conditions.

In the OPER mode, the 50VDC Power Supply module green DC ON LED is turned ON.

The Transmitter system is now ready to be keyed (PTT).

For detailed operation instructions refer to the T-4180 manual.

3.3.3

Transmitter External Control Protocol

The T-4180 provides external RS-232/RS-422 control of the transmitter from a PC. Refer to the T-4180
manual.

3.3.4

Continuous Bit Operation

During operation a number of critical functions are monitored to detect performance degradation or faults.
The conditions monitored in each of the modules comprising the COM5000-8 and in the rack cabinet
system as well as “external” conditions monitored are described in the following.

Faults are indicated by fault LED's on the System Controller front panel and on the four PA module front
panels. (Note: Momentary flashing of a fault LED does not indicate a fault. The LED must be on
continuously to indicate a fault.)

«
...
25
26
27
28
29
...
»

Содержание COM5000-8



































































Отзывы:

Нет отзывов

Похожие инструкции для COM5000-8

Бренд: Accuphase Страницы: 23

Бренд: NAD Страницы: 70

Бренд: Fender Страницы: 12

Бренд: FLC ELECTRONICS Страницы: 9

Бренд: Opvimus Страницы: 2

Бренд: Lanzar Страницы: 13

Бренд: Harman Kardon Страницы: 11

Бренд: B&K Страницы: 16

68 Custom Princeton Reverb

Бренд: Fender Страницы: 12

Бренд: Onkyo Страницы: 60

Series VII Aphrodite

Бренд: Hifonics Страницы: 58

Бренд: Anthem Страницы: 12

Бренд: Takstar Страницы: 2

Бренд: Labgear Страницы: 2

Бренд: icon Audio Страницы: 10

JBL PARTYBOX710

Бренд: Harman Страницы: 26

Бренд: rauland Страницы: 16

Бренд: Marantz Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды