16
Operating controls
EN
Charging the battery
WARNING !
Electrolyte liquid even discharges from
sealed batteries.
Â
Risk of injury and fire
¾
Avoid tilting the battery.
Î
Before using for the first time, charge the battery
with a 12 Volt battery charger.
• Lead-acid battery:
Maximum charging current 4 amps for 1-2 hours
• AGM battery:
Maximum charging current 1.1 amps for 12-
14 hours
Î
After charging the battery, first pull out the battery
charger plug.
Î
Then disconnect the battery (see also operating
instructions for the battery charger).
Attention !
¾
Follow the instructions in the operating manual
for your battery charger.
Operating controls
Overview
A
1
Forward pedal
2
Reverse pedal
3
Clamping lever for steering column
4
Cutting height adjustment lever
5
Throttle / choke*
6
Choke*
7
Display cluster*
8
PTO switch
9
Ignition lock*
10
Fuel tap
11
Fuel tank
12
Tank level indicator*
13
Gear release lever
14
Trailer coupling*
15
Can holder
16
Seat adjustment lever*
17
Steering wheel
18
Switch for parking brake / speed control
19
Brake pedal
(* model-dependent)
Start-up
Before operating the unit, always
Check:
• all protective features
• the engine-oil level (see the engine handbook)
• the fuel level
• tyre pressure
• the side coverings, accessory equipment, the
area around the air filter for dirt and grass
Fill up with fuel and check the oil level
Note
The engine has already been filled with oil in
the factory – please check the oil, if required
refill.
Î
Use unleaded petrol.
Î
Fill fuel tank up to max. 2 cm below the lower
edge of the inlet nozzle.
Î
Seal the fuel tank tightly.
Î
Check the oil level. The oil level must be between
the "Full/Max." and "Add/Min." mark (see also
engine manual).
Check tyre pressure
Î
Check the tyre pressure on all wheels and correct
it where necessary (for max. tyre pressure, see
tyre wall).
Setting the driver's seat
Y
(depending on
model and design)
Note
Depending on the design, the device may
have an adjustable seat with a built-in pres-
ence sensor.
Longitudinal adjustment
Ya
Î
Sit on the driver’s seat.
Î
Press the adjustment lever to the left and keep it
held
1
.
Î
Bring the seat to the desired position
2
and leave
the adjusting lever
3
.
Note
When releasing the adjustment lever, make
sure the seat latches in correctly.
Adjusting the armrests
Yb
Î
Move the armrests upwards
1
.
Î
Turn the adjusting segment
into the required posi-
tion
2
:
-
0 = Lowest position
-
3 = Highest position
Î
Move the armrests downwards.
Fitting the steering column
Bb
Upper part [B] of the steering column
Î
Release the clamping lever in an anti-clockwise
direction
3
.
Î
Tip the steering column
forwards into the required
position
4
.
Î
Tighten the clamping lever in a clockwise direc-
tion
3
to lock the steering column in this position.
Содержание 17CIDGHB603
