Cromtech Brumby CTG3000i Скачать руководство пользователя страница 36

Страница: 36 / 44

SPARK PLUG SERVICE

To ensure proper engine operation, the spark plug must be

properly gapped and free of deposits.

Recommended spark plug: LG R6

1. Open and lift away the left top cover.

Remove the spark plug cap and wire.

3. Clean any dirt from around the spark plug base.

Use the supplied wrench to remove the spark plug.

Visually inspect the spark plug. Discard it if the insulator

is cracked or chipped, or the electrode is worn out.

Clean spark plug with wire brush if it is to be reused.

Measure the plug gap with a feeler gauge - Gap should

be 0.7 to 0.8mm (0.028-0.031in).

8. Correct as necessary by carefully bending side electrode

Install the spark plug carefully, by hand, to avoid cross-

threading.

10. After a new spark plug has been seated by hand, it

should be tightened 1/2 turn with a wrench to compress

the gasket. If a used plug is being reinstalled, it should

only require 1/8 to 1/4 turn after being seated.

11.

Reinstall the spark plug cap securely on the spark plug.

12. Replace the left top cover, snapping it in place.

CAUTION: The spark plug must be securely tightened.

An improperly tightened plug can become very hot and

possibly damage the generator.

• Never use a spark plug with an improper heat range

•

Always use an WR7DC resistor-type spark plug. Using

a non-resistor spark plug will interfere with AC output

and the electronics, and may prevent the engine from

starting.

V
Hz

Pg. 36

Содержание CTG3000i













































Результаты поиска

Содержание CTG3000i

Отзывы:

Похожие инструкции для CTG3000i

Бренды по названию

Популярные бренды

Cromtech Brumby CTG3000i, Руководство пользователя

Результаты поиска

Содержание CTG3000i

Отзывы:

Похожие инструкции для CTG3000i

Бренды по названию

Популярные бренды