Creative Playthings WILLIAMSBURG SH 3200-000 Скачать руководство пользователя страница 5

Страница: 5 / 18

WILLIAMSBURG WITH TENT ROOF

19687-100 Rev U (09-20)

Assembly

Page 5

PRE ASSEMBLY INFORMATION

Lag Screw

Flat Washer

CREATIVE PLAYTHINGS PLAY SETS USE A FEW STANDARD CONNECTIONS. BECOMING FAMILIAR

WITH THESE CONNECTIONS WILL SIMPLIFY ASSEMBLY AND INSURE A SAFER PLAY PRODUCT

FOR YOUR CHILDREN.

Hex Bolt & Weld Nut Assembly Procedure:

Typical Installation - Lag Screws:

• Tap the head of the Lag Screw

with a hammer to start the

threads into the wood and then

use a 9/16" socket to tighten.

• DO NOT over tighten

Typical Installation - Wood Screws:
•  Use an electric drill or screw gun to drive screws.
•  Drill 1/8" pilot holes where required.
•  We recommend that you lubricate the

threads of the screws with beeswax or

soap to ease installation and minimize

breaking screws.

• It is very important to make certain

that the tops of all screws are flush

with the surface of the wood and there

are no protruding sharp edges.

Assembly Layout:

Align the holes in the parts to be fastened. Start preliminary

tightening of bolt into weld nut by hand. Tighten each bolt

with a wrench until the lock washer is fully compressed be-

tween the head of the bolt and the flat washer. See Illustra-

tions 5 and 6.

Correct Assembly:

Bolt has been screwed securely into weld nut and the connec-

tion is tight. Check connections periodically for tightness dur-

ing the life of the play set . Do not over tighten.

Incorrect Assembly:

During assembly or maintenance the bolt protrudes 1/8" past

the weld nut. Call customer service or replace the bolt at a lo-

cal hardware store. You may be overtightening or using the

wrong size bolt.

Failure to replace this bolt with a shorter one could result

in serious injury.

All hardware on this set is specially coated for corrosion resistance. If non-

Creative Playthings hardware is used, it MUST be galvanized or stainless

steel.

Содержание WILLIAMSBURG SH 3200-000


















Результаты поиска

Содержание WILLIAMSBURG SH 3200-000

Отзывы:

Похожие инструкции для WILLIAMSBURG SH 3200-000

Бренды по названию

Популярные бренды

Creative Playthings WILLIAMSBURG SH 3200-000, Инструкция по сборке

Результаты поиска

Содержание WILLIAMSBURG SH 3200-000

Отзывы:

Похожие инструкции для WILLIAMSBURG SH 3200-000

Бренды по названию

Популярные бренды