Creative Playthings WILLIAMSBURG SH 3200-000 Скачать руководство пользователя страница 18

Страница: 18 / 18

WILLIAMSBURG WITH TENT ROOF
19687-100 Rev U (09-20)

Page 18

ASSEMBLY INSTRUCTIONS

STEP 28 — Hole Caps:

Make a final check to make sure all the bolts and screws have been

tightened.
Locate the 1" Hole Caps. Install hole caps into all the counter-bored

holes to cover and protect the hardware.

STEP 27 — Slide:

Place the slide in the opening resting on the slide mount,

projecting straight out from the tower. Your slide may have stops

that indicate placement. If so, pull the slide tight against the

platform support. If your slide does not have stops check the un-

derside of the slide to judge how far to overlap the slide mount.

Make sure the holes in the slide are over the slide mount.
Make sure the slide extends out perpendicular from the play set.
Drill 5/16" holes through the slide, slide mount and platform

Boards using the indents in the slide as a guide. Fasten the slide

using one 1/4 x 3" Truss Head Bolt and one 1/4" Weld Nut for

each hole.

Save all instruction sheets and receipts in case it becomes necessary to contact Cre-

ative Playthings for warranty service and/or part replacement. The warranty can be

found in your Owner’s Manual.

Please fill out the warranty card on the back of your owners manual. Your completed

warranty card will allow us to quickly process warranty claims.

Thank you.

1/4 x 3" Truss

Head Bolts

Содержание WILLIAMSBURG SH 3200-000


















Результаты поиска

Содержание WILLIAMSBURG SH 3200-000

Отзывы:

Похожие инструкции для WILLIAMSBURG SH 3200-000

Бренды по названию

Популярные бренды

Creative Playthings WILLIAMSBURG SH 3200-000, Инструкция по сборке

Результаты поиска

Содержание WILLIAMSBURG SH 3200-000

Отзывы:

Похожие инструкции для WILLIAMSBURG SH 3200-000

Бренды по названию

Популярные бренды