Creative Playthings WILLIAMSBURG SH 3200-000 Скачать руководство пользователя страница 11

Страница: 11 / 18

WILLIAMSBURG WITH TENT ROOF

19687-100 Rev U (09-20)

Assembly

Page 11

ASSEMBLY INSTRUCTIONS

STEP 6 — Outside Stringers:

Mount the Outside Stringers (H) to the inside

of the left and right corner posts. Attach each

outside stringer using two 5/16 x 5-1/2" hex bolt

assemblies as shown.
Start the bolt from the outside of the tower. Push

each bolt through the bottom hole in the left or

right platform sides and the corner posts before

passing through the outside stringer. Make sure

the platform sides and outside stringers align

across the bottom edges.
Hint: The holes in the outside stringers are offset

from the center of the board; you may have to

flip the board to achieve proper alignment.

STEP 7 — Inside Stringers

Mount the Inside Stringers (G) between the plat-

form ends.
Attach each inside stringer using two 5/16 x 4"

lag screws and flat washers as shown. Make sure

the outside stringers and inside stringers align

across the top edge.

Move the tower to the final intended postion. Use a Carpenter's level to assure the base is level and the

posts are plumb.

Platform End

Omitted for

Clarity

5/16 x 5-1/2"

Hex Bolts

5/16 x 4" Lag

Screws

Содержание WILLIAMSBURG SH 3200-000


















Результаты поиска

Содержание WILLIAMSBURG SH 3200-000

Отзывы:

Похожие инструкции для WILLIAMSBURG SH 3200-000

Бренды по названию

Популярные бренды

Creative Playthings WILLIAMSBURG SH 3200-000, Инструкция по сборке

Результаты поиска

Содержание WILLIAMSBURG SH 3200-000

Отзывы:

Похожие инструкции для WILLIAMSBURG SH 3200-000

Бренды по названию

Популярные бренды