Creative Playthings WILLIAMSBURG SH 3200-000 Скачать руководство пользователя страница 1

Страница: 1 / 18

MODEL #SH 3200-000

ASSEMBLY MANUAL

WILLIAMSBURG

TENT

ROOF

with

Carefully read the owner’s manual and all instructions

before assembling your play set. It provides additional

information on the care and use of your play set.
Creative Playthings takes great care to design its products

with your child’s safety in mind. However, only with careful

supervision and proper safety instructions, can you be

assured of safe play time on any product designed for

children.

This product is intended for single family home/residential use only

and not intended for use in any public setting. Placement in any public

setting constitutes a misuse of this product.

All hardware on this set is

specially coated for corrosion

resistance.

If non-Creative Playthings

hardware is used, it must be

galvanized or stainless steel.

Creative Playthings

33 Loring Drive, Framingham, MA 01702

www.creativeplaythings.com

Содержание WILLIAMSBURG SH 3200-000


















Результаты поиска

Содержание WILLIAMSBURG SH 3200-000

Отзывы:

Похожие инструкции для WILLIAMSBURG SH 3200-000

Бренды по названию

Популярные бренды

Creative Playthings WILLIAMSBURG SH 3200-000, Инструкция по сборке

Результаты поиска

Содержание WILLIAMSBURG SH 3200-000

Отзывы:

Похожие инструкции для WILLIAMSBURG SH 3200-000

Бренды по названию

Популярные бренды