Technical Manual
87
Se
cti
o
n
10
- D
ia
gn
o
stic
an
d
Ma
in
te
n
an
ce
P
ro
ce
d
u
re
s
A FRESH APPOACH TO VENDING
10.3.2 Weekly Cleaning Procedure
Important! Cleaning and maintenance outlined below must be completed on a
weekly basis.
1. Check that the Oltre brewer(s) are in an open position, if not then press ‘2’ on the
service keypad, the brewer will move and will stop at the open position
2. Remove the brewer chamber & filter belt assembly, then remove the belt. Clean all
components with the recommended mix of de-staining solution; soak for 5 to 10
minutes.
3. Rinse all parts thoroughly in clean water & re-assemble into the machine.
4. Press the service keypad Brewer Clean button ‘4’ and the machine will flush the
brewer.
5. Empty the brewer waste container. Wash the waste container thoroughly.
N.B. If the feature has been turned on when the brewer waste container is emptied the
waste counter must be reset. To reset the waste counter press button ‘12’ on the service
keypad, two audible bleeps confirm that the counter has been reset to zero.
10.4 System Drain Down - B2C Machines Only
Should it become necessary for the engineer to do any work on the B2C water system it is
very important that the following sequence is followed to ensure safe working as well as
correct system fill and heating when the machine is powered up.
10.4.1 Cooling down the B2C system
1. Open the front door of the machine. Using the service keypad located in the rear
of the door, press the ‘Machine Cool Down’ button (10) to ensure the system is
cooled. Approximately 600ml of cold water is flushed through the system and out
to the waste bucket.
Important: Pressing button 10 also informs the machine software that the B2C
system has been drained ensuring that the B2C system will automatically fill before
heating on power up. This is very important and must not be overlooked.
2. Once the B2C system has been cooled the LCD will display the message ‘Machine
cooled’ and water will stop pumping through the system. Remove the waste
bucket and empty the contents before re-fitting to the machine. Ensure all pipes
etc. are refitted correctly into the bucket.
3. Turn off the power to the machine.
Содержание Voce Media
