Crane STEP1042L Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 26

background image

Inner Seal-

To expose inner shaft seal (10) for examination,

remove outer seal as outlined above. Remove socket head cap
screws (8) and (38). Lift seal plate (12) and square-ring (7) from
intermediate coupling (9). If replacement is required, drain oil
from motor housing per paragraph F-1.3, then remove retaining
ring (11), retaining ring (10b), spring (10c) and rotating member
(10d) from shaft. Examine as outlined in outer seal paragraph.
If replacing seal, remove stationary (10a) by prying out with flat
screw driver.

F-3.2) Reassembly:
Inner Seal-

Clean and oil seal cavities in seal plate (12). Lightly

oil (

DO NOT

use grease) outer surface of stationary member

(10a). Press stationary member (10a) firmly into intermediate
coupling (9), using a seal pusher (see parts list- seal tool kit).
Nothing but the seal pusher is to come in contact with seal face
(see Fig. 5).

IMPORTANT !

DO NOT HAMMER ON THE SEAL PUSHER- IT WILL

DAMAGE THE SEAL FACE.

Make sure the stationary member is in straight. Slide a bullet
(see parts list-seal tool kit) over motor shaft. Lightly oil (

DO

NOT

use grease) shaft, bullet and inner surface of bellows on

rotating member (10b) see Fig. 6. With lapped surface of
rotating member (10b) facing inward toward stationary
member (10a), slide rotating member (10b) over bullet and
onto shaft, using seal pusher, until lapped faces of (10a) and
(10b) are together (see Fig. 4).

IMPORTANT !

IT IS EXTREMELY IMPORTANT TO KEEP SEAL FACES

CLEAN DURING ASSEMBLY. DIRT PARTICLES

LODGED BETWEEN THESE FACES WILL CAUSE THE

SEAL TO LEAK.

PUMP END

(OUTBOARD END)

MOTOR END

(INBOARD END)

SEAL ASSEMBLY

(10)

SEAL PLATE (12) or

INTERMEDIATE (9)

SPRING (10c)

ROTATING MEMBER (10b)

STATIONARY (10a)

Fig. 4

RETAINING RING (10d)

RETAINING RING (11)

SEAL PLATE (12) or

INTERMEDIATE COUPLING (9).

SEAL PUSHER

STATIONARY MEMBER

(10a) Polished Face Out.

Fig. 5

MOTOR & INTERMEDIATE

COUPLING

STATIONARY (10a)

BULLET

ROTATING

MEMBER (10b)

SEAL

PUSHER

Fig. 6

10

«
...
8
9
10
11
12
...
»

Содержание STEP1042L



























Отзывы:

Нет отзывов

Похожие инструкции для STEP1042L

Бренд: Qual Craft Страницы: 5

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 57

Бренд: YAMADA Страницы: 84

Бренд: Annovi Reverberi Страницы: 18

COBRA DS 0600 E

Бренд: BUSCH Страницы: 24

Бренд: Kospel Страницы: 40

Johnson Pump CombiProLine OH3

Бренд: SPX FLOW Страницы: 67

Tranquility Low-Profile Series

Бренд: ClimateMaster Страницы: 76

Бренд: Kessel Страницы: 24

Бренд: Energie Страницы: 31

HYDRA-SPRAY President A Series

Бренд: Graco Страницы: 20

Бренд: F.F. Group Страницы: 28

Бренд: Zodiac Страницы: 36

Бренд: Annovi Reverberi Страницы: 4

Бренд: Remco Страницы: 5

FLOJET G55 Series

Бренд: Xylem Страницы: 2

Бренд: Dirty Hand Tools Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды