Crane STEP1042L Скачать руководство пользователя | Manualshive

Страница: 21 / 26

background image

IMPORTANT !

WARRANTY REGISTRATION

Your product is covered by the enclosed Warranty.

Complete the Warranty Registration Form and returned to

Crane Pumps & Systems, Inc. Warranty Service Group

IMPORTANT! If you have a claim under the provision of the warranty,

contact your local Crane Pumps & Systems, Inc. Distributor.

RETURNED GOODS

RETURN OF MERCHANDISE REQUIRES A "RETURNED GOODS AUTHORIZATION".

CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR.

   Products Returned Must Be Cleaned, Sanitized,
   Or Decontaminated As Necessary Prior To Shipment,
   To Insure That Employees Will Not Be Exposed To Health
   Hazards In Handling Said Material. All Applicable Laws
   And Regulations Shall Apply.

21

«
...
19
20
21
22
23
...
»

Содержание STEP1042L



























Отзывы:

Нет отзывов

Похожие инструкции для STEP1042L

Бренд: Calpeda Страницы: 16

Бренд: Zoeller Страницы: 4

Бренд: Mallory Страницы: 7

Бренд: Water Worker Страницы: 2

Bell & Gossett ecocirc XL Series

Бренд: Xylem Страницы: 62

Бренд: I.VA.CO. Страницы: 12

Craftsman 390.269451

Бренд: Sears Страницы: 8

Бренд: EMI Страницы: 5

Бренд: Endress Страницы: 17

Exubera Pro UC EV9333-50

Бренд: Everpure Страницы: 2

Бренд: Noritz Страницы: 120

Бренд: A.O. Smith Страницы: 4

Бренд: Battery Watering Technologies Страницы: 2

Бренд: OSNA Страницы: 40

Бренд: Swim & Fun Страницы: 136

Бренд: Rheem Страницы: 50

Бренд: Launtop Страницы: 22

Бренд: vacuubrand Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды