Crane Barnes Simplex OGV Series Скачать руководство пользователя

Страница: 21 / 25

STEPS & TIPS:

• Conduit Must Be Sealed To Prevent Water Infiltration

( Fig. 19).

• Peal and Place Gasket on Clean/Dry Basin Rim

Surface Inside Bolt Circle.

• Before installing the cover make certain that all cords

are tied up and clear of pump and level control.

STEP 11.

Sealing of Control Panel Conduit and

Installation of Cover Gasket

FIGURE 19

START UP PRE-CHECKLIST

BEFORE STARTING UP YOUR UNIT, CHECK THE FOLLOWING ITEMS:

INSTALLATION QUESTIONS:



Was A Proper Bedding Material Used



Is Basin Installed Level (within A Half Of Bubble)



Was The Proper Amount And Type Of Ballast Used



Was Backfill And Compaction Done To ASTM-D2321 To Properly Support Piping



Is The Inlet Location Provide Clear Removal Of Pump And Have A 1/8” Per Foot Drop



Are All Penetrations Through The Basin Wall Sealed Water-tight



Are All Piping Connections Tight And Required Valves Installed Properly



Has A Minimum Of 32 Inches Of Water Been Put Into The Tank



Has The Vent Been Installed On The Cover, If Required (Polycover Have Vent Factory Installed)



Varify All Valves Are Open

ELECTRICAL QUESTIONS:



Is The Junction Box Dry (if Applicable)



Are All Of The Cord Grips Tight



Are All Wiring Connections Secured



Is The Junction Box Cover Tight



Are All Cords Secured And Clear Of The Pump



Is The Control Panel Securely Mounted



Is The Control Panel Dry



Is The Conduit Entering The Control Panel Sealed (J-Box Units ONLY)



Are All Wiring Connections Secured



Turn The Circuit Breaker In Control Panel To “Off” Position



Turn The Circuit Breaker In The Service Drop/HouseHold Breaker Panel To The “On” Position

FIGURE 20

Sealing of Conduit Entering Electrical Enclosure

Содержание Barnes Simplex OGV Series


























Результаты поиска

Содержание Barnes Simplex OGV Series

Отзывы:

Похожие инструкции для Barnes Simplex OGV Series

Бренды по названию

Популярные бренды

Crane Barnes Simplex OGV Series, Руководство по установке

Результаты поиска

Содержание Barnes Simplex OGV Series

Отзывы:

Похожие инструкции для Barnes Simplex OGV Series

Бренды по названию

Популярные бренды