Crane Barnes SGV 2 HP страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 32

background image

14

Motor Housing

NOTE:

Position unit upright, using 4” pvc

coupler to avoid resting unit on the lower
shaft.

Loosen cable clamp bolts and lock washers from
motor housing. Remove cord from motor housing by
pulling straight up while using a rocking motion.

Remove retaining snap ring with a medium ﬂ at tip screwdriver. Using a 1/4-20 bolt, thread it into
the center of the terminal block. Pull straight up with a rocking motion to remove the terminal block.
Disconnect all wire connections noting where each wire is connected. The bottom of the block has a
number located next to each pin for reference. If pump is equipped with temperature-moisture sensors,
remove in same manner as the power cord.

19

22

23

24

21

20

«
...
12
13
14
15
16
...
»

Содержание Barnes SGV 2 HP

































Отзывы:

Нет отзывов

Похожие инструкции для Barnes SGV 2 HP

Бренд: BADU Страницы: 60

Бренд: T.I.P. Страницы: 24

Бренд: Taco Страницы: 56

Бренд: Taco Страницы: 12

Бренд: Gardena Страницы: 16

Бренд: Calorex Страницы: 2

Бренд: DROPSA Страницы: 9

Бренд: DAB Страницы: 72

Бренд: Olimpia splendid Страницы: 72

Бренд: VARISCO Страницы: 18

Бренд: Bryant Страницы: 54

Бренд: FE PETRO Страницы: 16

Бренд: Drazice Страницы: 28

Бренд: samhydraulik Страницы: 9

Бренд: Trigano PISCINES Страницы: 13

Бренд: Wacker Neuson Страницы: 52

Бренд: Kärcher Страницы: 68

EKHWS 150D3V3 Series

Бренд: Daikin Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды