Crane Barnes SGV 2 HP Скачать руководство пользователя | Manualshive

Страница: 19 / 32

background image

19

SGV 2 HP Assembly

Bearings to Pump Rotor

When replacing bearings, be careful not to damage the rotor or shaft threads. Using an arbor press, hold
the rotor and press the upper bearing on the rotor shaft, applying force to the inner race of the bearing
only. Install top retaining ring on rotor shaft. Using an arbor press, hold the rotor and press the lower
bearing on the rotor shaft, apply force to the inner race of the bearing only. Install bottom-retaining ring on
rotor shaft. The bearing will be positioned between the retaining rings.

Intermediate Coupling Component Parts

If pump is equipped with optional moisture sensors, apply thread compound (Permatex) to threads on
probes and install in intermediate coupling. Connect wires to probes with machine screw. Note: If pumps
are not equipped with moisture sensors, probes will be replaced by pipe plugs, install with permatex.

«
...
17
18
19
20
21
...
»

Содержание Barnes SGV 2 HP

































Отзывы:

Нет отзывов

Похожие инструкции для Barnes SGV 2 HP

Бренд: VEAB Страницы: 4

Altherma EHVZ04S18DA6V

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 8

Altherma EAVZ16S18DA6V

Бренд: Daikin Страницы: 20

Бренд: Daikin Страницы: 56

altherma EJHA04AAV3

Бренд: Daikin Страницы: 16

DynaFLO DOWB-S1 Series

Бренд: Camus Hydronics Страницы: 28

NEVERCOLD 70600

Бренд: EASTMAN Страницы: 11

Бренд: Crivit Страницы: 23

Бренд: Day and Night Страницы: 18

Бренд: Astral Pool Страницы: 35

Smartmax Series

Бренд: ubbink Страницы: 29

Бренд: Daikin Страницы: 40

Бренд: Calpeda Страницы: 19

Бренд: Unitary products group Страницы: 24

Sanitary Series

Бренд: TapFlo Страницы: 50

Warren Rupp SANDPIPER Beast SPB20

Бренд: Idex Страницы: 21

Бренд: Waterous Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды