Crane Barnes SGV 2 HP страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 32

background image

25

Outer Seal

Clean and oil stationary seal cavity in seal plate. Slide seal guide (see parts list - Seal Tool Kit) over motor
shaft. Lightly oil (do not grease) outer surface of stationary seal. Press stationary seal ﬁ rmly into seal
plate using a seal pusher. Make sure the stationary member is in straight. Nothing but the seal pusher is
to come in contact with seal face.

CAUTION: DO NOT HAMMER ON THE SEAL PUSHER - IT WILL DAMAGE THE SEAL FACE.

With seal guide over motor shaft, lightly oil

(DO NOT grease)

guide, shaft, and inner surface of bellows

on rotating seal. With lapped surface of rotating member facing inward toward stationary member, slide
rotating member over guide and onto shaft, using seal pusher, until lapped faces of the stationary and
rotating seal are together. Place spring over shaft and the rotating member. Make sure it is seated on the
retainer and not cocked or resting on bellows tail.

NOTE: Discard seal spring cap (Included in Rebuild Kit)

51

50

53

52

«
...
23
24
25
26
27
...
»

Содержание Barnes SGV 2 HP

































Отзывы:

Нет отзывов

Похожие инструкции для Barnes SGV 2 HP

Бренд: Danfoss Страницы: 26

Бренд: Calpeda Страницы: 80

Бренд: Danfoss Страницы: 24

Бренд: DAYLIFF Страницы: 12

VRV EMERION RXYQ-AATJA

Бренд: Daikin Страницы: 429

Бренд: A.O. Smith Страницы: 4

Delta Solo Compact MVP Series

Бренд: KSB Страницы: 40

Бренд: CET Страницы: 23

AQUAPRO AP1000FP

Бренд: Aquatec Страницы: 2

Бренд: Gardner Denver Страницы: 27

Бренд: EBARA Страницы: 20

Comfort 5000/5 LCD

Бренд: Gardena Страницы: 13

DRENAG 1000-1200

Бренд: Saci Страницы: 134

Lincoln 215-M049

Бренд: SKF Страницы: 45

Бренд: Wacker Neuson Страницы: 52

Бренд: Virax Страницы: 52

EKHWS 150D3V3 Series

Бренд: Daikin Страницы: 20

Бренд: Barnes Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды