CountyLine CL100 1 HP Скачать руководство пользователя страница 8

Страница: 8 / 24

1. Thread 1-1/4" close nipple into

foot valve. Thread the other
end of 1-1/4" close nipple into
bottom of deep well ejector. Hand
tighten, then tighten 1/4 turn with
pipe wrench.

2. The ejector has two holes in

the top of it. Confirm nozzle is
installed. Thread deep well venturi
tube (longer tube) into larger
hole until snug. Thread 1" x 5"
nipple into smaller hole. Only
hand tighten venturi tube. Hand
tighten nipple 1/4 turn with pipe/
crescent wrench.

3. Thread a 1-1/4" male PVC

adapter over the venturi tube
and into ejector. Thread a 1"
female PVC adapter onto the
1" x 5" nipple. Hand tighten
adapters 1/4 turn with pipe/
crescent wrench.

4. Subtract five feet from the

depth of your well. This is the
total length of PVC pipe and
couplings to cement onto both
1-1/4" male and 1" female PVC
adapters. Cement a section of
PVC pipe to each adapter, then
lower the whole assembly into
the well, foot valve first. Firmly clamp the end of
the PVC pipes with a pipe clamp to prevent the
assembly from sliding down into well.

5. Cement as many

couplings and
sections of rigid
PVC pipe on both
the pressure and
delivery sides as
it takes to equal
the depth of your
well minus four
feet, then firmly
clamp the assembly
with a pipe clamp
to prevent the
assembly from
sliding down into
the well. Be sure to
keep track of which
pipe is the pressure
pipe and which is
the delivery pipe.

To Install a Deep Well Pump

(CL520, CL100, 4" or Larger Diameter Cased Well)
For wells more than 25, but not exceeding 70 feet
in depth, the 1 HP convertible deep well pump is
recommended. However, the 1/2 HP deep well pump
may also be used for depths not exceeding 70 feet.
General materials needed for the convertible pumps:
•  One can PVC cement (read instructions carefully)
•  One roll PTFE pipe thread sealant tape
•  Two 1" female PVC adapters
•  Enough rigid 1-1/4" and 1" PVC pipe and couplings

to reach from bottom of well to pump (delivery pipe)

•  One 1-1/4" PVC elbow
•  One 1-1/4" male PVC adapter
•  One pressure regulator kit (includes fittings, tubing,

and 1/4" plug)

• One pressure gauge
• Two male 3/4" PVC adapters

• Enough rigid 3/4" PVC pipe to reach from pump to

pressure tank to service line

•  Tank tee (for diaphragm pressure tanks)
•  Two 1/4" plugs
•  One 1/2" drain cock
In addition to General Materials for Deep Well Pumps
•  One 1-1/4" foot valve
•  One 1-1/4" close nipple
•  One ejector
•  One 1" x 5" nipple
•  One 1-1/4" female adapter
•  One well seal
•  Enough rigid 1" PVC pipe and couplings to reach

from bottom of well to pump (pressure pipe)

•  One 1" PVC elbow
•  Two 1-1/4" male PVC adapters
•  One 1" x 4" nipple

Reminder: All joints and connections must be airtight . A single pinhole leak will prevent the proper operation of
the pump . Use thread compound on all threaded connections unless specified otherwise .

1-1/4"

NIPPLE

EJECTOR

FOOT

VALVE

1" FEMALE

PVC

ADAPTER

1-1/4" MALE

PVC

ADAPTER

1" FEMALE