Cormach MEC 10, Техническое руководство по обслуживанию

Страница: 32 / 39

Technical Support Manual – 05/2018 Rel. 2.1.3 Page 30
How to exit the MOTO wheel type calibration
At any time it is always possible to exit the calibration procedure during its progress by pressing repeatedly [F+P3] keys
The machine will return to the SERVICE mode displaying the writing
SER SER
. To return to the NORMAL
mode, press [F+P3] keys again. The calibration in progress will be cancelled and the machine will use the
values of MOTO wheel type calibration which were previously stored. Also in this case the MOTO wheel type and the ALU1 Program
Type will remain set. The wheel dimensions will be those which were automatically set by the machine for this kind of calibration.
7. ERROR CODES AND WARNINGS
The machine indicates error conditions by alternating the display of the error code with a brief description (in English) of the cause
of the error.
The machine displays the code for different times depending on the code of said error, as indicated in the "Display" column in table
T7.1.
Table T7.1: Error codes
Code Brief
description
Models Display
(1)
Description Notes
000 a 009
INT ERR
MEC
5-10-15-20
ERROR: Machine parameters
internal error.
Replace CPU.C1C.X board.
010
REV SPN
MEC
5-10-15-20
ERROR: Reverse rotation of
the wheel.
Replace power supply board.
020
NO EEP
MEC
5-10-15-20
OPERATOR
CONFIRMATION
ERROR: Lack of
communication with the
eeprom memory.
Turn the machine off and then on again. If the
error persists, replace the CPU.C1C.X board.
011
SPD LOW
MEC
5-10-15-20
WARNING: Wheel speed too
low.
- Check the mains voltage.
- Check the tension of the belt and pulley.
012
NO STP
MEC
5-10-15-20
ERROR: The wheel cannot be
stopped at the end of the
launch.
Check the ENCODER board.
Check the power supply board.
013
SPD HIG
MEC
5-10-15-20
ERROR: Wheel speed too
high.
Replace the power supply board.
014
NO SPN
MEC
5-10-15-20
ERROR: The wheel does not
spin.
1. Power supply board.
2. CPU.C1C.X board.
3. ENCODER board.
015
Codice del
tasto
danneggiato
MEC
5-10-15-20
PERMANENT
UNTIL TURNED
OFF
ERROR: Damaged keys upon
activation.
Release all buttons, then turn off or restart the
machine. If the error persists, replace the
CPU.C1C.X board.
016
DIS OUT
MEC
10-15-20
OPERATOR
ACTION
OR OPERATOR
CONFIRMATION
WARNING: Distance sensor is
not in rest position at start-up
of the machine or when [P8]
Start is pressed.
Set the sensor to its rest position: the error
should disappear. If the error persists, contact
technical support.
NOTE: if [F+P2] is pressed the machine
acquisition system is temporarily disabled and
operation can be continued. The disabled
status will last until the machine has been
turned off. The red LED [6] in figure F3.1 flashes
to indicate the temporary disabled status.
017
LAR OUT
MEC
10-15-20
OPERATOR
ACTION
OR OPERATOR
CONFIRMATION
WARNING: Width sensor is
not in rest position at start-up
of the machine or when [P8]
Start is pressed.
Set the sensor to its rest position: the error
should disappear. If the error persists, contact
technical support.
NOTE: if [F+P2] is pressed the machine
acquisition system is temporarily disabled and
operation can be continued. The disabled
status will last until the machine has been
turned off. The red LED [6] in figure F3.1 flashes
to indicate the temporary disabled status.
019
NO CP
MEC
5-10-15-20
OPERATOR
CONFIRMATION
WARNING: Communication
processor failure.
Turn the machine off and then on again. If the
error persists, contact technical support.
The machine can still be used but all functions
related to the USB port are disabled.