manualshive.com logo in svg

Cormach MEC 10, Техническое руководство по обслуживанию

Поделиться
Скачать
Cormach MEC 10 Скачать руководство пользователя страница 12

 

Technical Support Manual – 05/2018 Rel. 2.1.3                         

Page 10 

Gau 

Activation or deactivation of the distance/diameter sensor 

This menu option allows you to activate or deactivate the distance-diameter sensor. This is a double function: if the function is 

disabled, press [F+P5] 

   to enable it and vice-versa. 

 

Description 

 

1 

Enter the SERVICE mode by pressing [F+P3]   

. 

 

2 

Press [F+P5] 

  to 

enter in PARAMETERS MENU. 

 

3 

A password is required to enter this menu. 
Enter the password by pressing the keys in 
the sequence indicated within 5 seconds, or 
the machine will return to SERVICE mode: 

1.

 

[P1] 

 

2.

 

[P4] 

 

3.

 

[P2] 

 

4.

 

[P5] 

 

 

4 

Press [F+P5]   

  to 

activate the DISTANCE/DIAMETER SENSOR 
GAUGE. The DISTANCE/DIAMETER SENSOR 
GAUGE IS ENABLED. 

 

5 

Press  [F+P5] 

  to 

deactivate  DISTANCE/DIAMETER SENSOR 
GAUGE. 

 

6 

To exit the Parameters Menu, select option 

Ret

 

and press [F+P5]

 

 

 

 
 
 
 
 

Содержание MEC 10








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды