background image

ElectroLynx® is a registered trademark of ASSA ABLOY Inc.

Copyright © 2014 Corbin Russwin, Inc. All rights reserved.

Reproduction in whole or in part without the express written 

permission of Corbin Russwin, Inc. is prohibited.

 

®

ASSA ABLOY

1

Installation Instructions

Mortise Lockset

For ML20800 TCAC2 Series

                   

Please read these instructions carefully to prevent missing important steps.

Please Note: 

Improper installation may result in damage to the lock and void the factory warranty.

Important: 

The accuracy of the door preparation is critical for proper functioning and security of this lock.

                   Misalignment can cause premature wear and a lessening of security. 

FM224   10/18

For installation assistance contact Corbin Russwin Inc., at 1-800-810-WIRE (9473)

 

C A U T I O N

DOOR MUST REMAIN OPEN

DURING INSTALLATION.

USE DOOR STOP.

1

2

3

4

7

5

8

0

6

9

#

*

TEST

FOR PROPER

OPERATION

BEFORE

CLOSING

DOOR

A

ccess

 

800

®

®

ASSA ABLOY

Attention Installer

In U.S.:
Corbin Russwin, Inc.
225 Episcopal Road
Berlin, CT 06037 USA
www.corbinrusswin.com

In Canada:
ASSA ABLOY Door Security Solutions Canada
160 Four Valley Drive
Vaughan, Ontario, Canada L4K4T9
www.assaabloy.ca

 WARNING

This product can expose  

you to lead which is  

known to the state of  

California to cause cancer 

and birth defects or other 

reproductive harm. For 

more information go to  

www.P65warnings.ca.gov.

08/2018

Содержание ASSA ABLOY Access800





















Отзывы: