Cooper & Hunter CH-HP3.0SWHK Скачать руководство пользователя

Страница: 44 / 44

Air Source Heat Pump Water Heater

Table 18-3

Please contact the

appointed service center in

case of any of following conditions.

The unit is shut down and E1 is

High pressure protection

The unit is shut down and E4 is

displayed on thecontroller.

Discharge protection

The unit is shut down and E5 is

displayed on the controller.

Compressor overload protection

The unit is shut down and E6 is

displayed on the controller.

Communication error

The unit is shut down and F3 is

displayed on the controller.

Outdoor temperature sensor error

The unit is shut down and F4 is

displayed on the controller.

Discharge temperature sensor error

The unit is shut down and F6 is

displayed on the controller.

Outdoor heat exchanger coil temperature

sensor e rror

The unit is shut down and Fd is

displayed on the controller.

Suction temperature sensor error

The unit is shut down and FE is

displayed on the controller.

Upper Water temperature sensor error

The unit is shut down and FL is

displayed on the controller.

Middle Water temperature sensor error

The unit is shut down and L6 is

displayed on the controller.

Insufficient unit capability

Harsh voice;

Disagreeable smell;

Air switch or circuit breaker tripping

frequently

There is probably the potential security

hazard

and it is high recommended to stop and

unplug the unit.

After-sales Service

If the air source water heater you purchase from

C&H

encounters quality problems

or other problems, contact your local maintenance centers authorized by

C&H

Symptom

Errors

Содержание CH-HP3.0SWHK













































Результаты поиска

Содержание CH-HP3.0SWHK

Отзывы:

Похожие инструкции для CH-HP3.0SWHK

Бренды по названию

Популярные бренды

Cooper & Hunter CH-HP3.0SWHK, Руководство пользователя

Результаты поиска

Содержание CH-HP3.0SWHK

Отзывы:

Похожие инструкции для CH-HP3.0SWHK

Бренды по названию

Популярные бренды