background image

Air Source Heat Pump Water Heater 

33 

15 Notes on Winter Use 

(1)temperatures in Winter are low. If the unit is not used for a long time, before 

starting the unit, connect it with electricity for at least 8 hours. 

(2)Outdoor temperatures in Winter are relatively low, do not disconnect the unit 

from electricity if it needs to be shut down for a short time. Otherwise, the automatic 

freeze-proof protection function will fail.

 

At low ambient temperatures, the automatic 

freeze-proof  protection  function  enables  the  unit  to  heat  the  water  before  water 

temperature approaches the freezing point. When the water temperature rises to a 

safe temperature, the function is disabled.

 

However, this function does not apply to 

the water inlet and outlet pipes of the water tank. If the ambient temperature is below 

0°C,  freeze-proof  bands  must  be  installed.  In  addition,  ensure  that  they  are 

energized. If the water tank is inevitably installed outdoors, reduce  the outdoor part 

of  pipes  including  the  refrigerant  connecting  pip  and  water  inlet  and  outlet  pips  of 

the water tank. Otherwise, the heat loss is large, power consumption increases, and 

the  water  system  is  vulnerable  to  freezing.

 

In  addition,  pay  attention  to  thermal 

insulation of special positions such as valve joints and pipe bends. Otherwise, these 

positions are vulnerable to freezing. 

(3)If the unit is not used for a long time, drain the water in the water tank and the 

pipes by following drain operations. Otherwise, the water system may be frozen and 

damaged.

 

Use  the  unit  after  the  water  is  drained  and  then  the  water  tank  is  full 

filled with water. 

Tips:

 

If  it  is  inconvenient  or  dangerous  to  perform  the  preceding  operations, 

directly contact  your  local  dealer  or  authorized service center  of

C&H

,  and

C&H

  will 

dispatch  professional  personnel  to  provide  inspection,  drainage,  water 

replenishment, commissioning, cleaning, and maintenance services. 

Содержание CH-HP3.0SWHK













































Отзывы: